DYNAMIC MODELING OF A MULTI-CHANNAEL VACUUM GRIPPER SYSTEM AND TRAJECTORY OPTIMIZATION FOR MANIPULATOR ROBOTS IN AUTOMATED GLASS SHEET SORTING AND TRANSFER LINES

Authors

  • Otakhonov Abdumaqsad Researcher, the department of Energetics engineering Fergana State Technical University Author

Keywords:

multi-channel vacuum gripper; glass sheet handling; manipulator dynamics; trajectory optimization; vacuum pressure dynamics; thin-plate bending

Abstract

 Automated sorting and transfer lines for thin and large-format glass sheets require high throughput while strictly preventing surface micro-cracks, bending deflection, and vacuum loss caused by inertial loads. This study presents an integrated dynamic model of a multi-channel vacuum gripper mounted on an articulated industrial manipulator robot, coupled with a time-energy optimal trajectory planning method for glass sheet handling. The coupled system dynamics combine rigid-body manipulator kinematics and dynamics with an airflow-capacitance vacuum pressure model and thin-plate bending behavior of the gripped glass sheet. Trajectory generation is formulated as a constrained optimal control problem using quintic B-spline parameterization and sequential quadratic programming (SQP) to minimize transfer time and actuator energy while bounding peak normal acceleration, jerk, and glass deflection. Simulation results for a 6-DOF manipulator handling a 1800 times 1200 times 4 mm float glass sheet across a 1.4m transfer stroke demonstrate a 24.6% reduction in cycle time and a 31.2% reduction in mechanical energy consumption compared to a conventional trapezoidal velocity profile, while maintaining maximum glass deflection below 0.42mm and vacuum safety factor above 2.8.

References

1.Ghanbarpour Asl, H. (2019). Minimum-time path planning for robot manipulators using path parameter optimization with external force and frictions. Tehnički glasnik, 13(1), 25–35. https://doi.org/10.31803/tg-20181112104935

2.Hou, J., Du, J., & Chen, Z. (2023). Time-optimal trajectory planning for the manipulator based on improved non-dominated sorting genetic algorithm II. Applied Sciences, 13(11), 6757. https://doi.org/10.3390/app13116757

3.Hou, R., Niu, J., Guo, Y., et al. (2022). A novel resolution scheme of time-energy optimal trajectory for precise acceleration controlled industrial robot using neural networks. Actuators, 11(5), 130. https://doi.org/10.3390/act11050130

4.Jiang, P., Oaki, J., Ishihara, Y., & Ooga, J. (2024). Multiple-object grasping using a multiple-suction-cup vacuum gripper in cluttered scenes. Robotics, 13(6), 85. https://doi.org/10.3390/robotics13060085

5.Maggi, M., Mantriota, G., & Reina, G. (2022). Influence of the dynamic effects and grasping location on the performance of an adaptive vacuum gripper. Actuators, 11(2), 55. https://doi.org/10.3390/act11020055

6.Martínez-Peral, F. J., Borrell Méndez, J., Segura Heras, J. V., & Perez-Vidal, C. (2024). Development of a tool to manipulate flexible pieces in the industry: Hardware and software. Actuators, 13(4), 149. https://doi.org/10.3390/act13040149

7.Wei, B., Liu, C., Zhang, X., et al. (2024). Smooth and time-optimal trajectory planning for robots using improved carnivorous plant algorithm. Machines, 12(11), 802. https://doi.org/10.3390/machines12110802

8.Xu, Z., Wang, W., Chi, Y., Li, K., & He, L. (2023). Optimal trajectory planning for manipulators with efficiency and smoothness constraint. Electronics, 12(13), 2928. https://doi.org/10.3390/electronics12132928

Downloads

Published

2026-11-19